View AD5750_4214402.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Industrial Current/Voltage Output Driver, Programmable Ranges
Preliminary Technical Data
FEATURES
Current Output Ranges: 4-20mA, 0-20mA or 0-24mA, 20ma, 24ma B Grade - 0.1% Total Unadjusted Error (TUE) A Grade - 0.3% Total Unadjusted Error (TUE) 5ppm/C Output Drift Voltage Output Ranges: 0-5V, 0-10V, 5V, 10V, 20% over-range B Grade - 0.1% Total Unadjusted Error (TUE) A Grade - 0.3% Total Unadjusted Error (TUE) Flexible Serial Digital Interface On-Chip Output Fault Detection PEC Error Checking Asynchronous CLEAR Function Power Supply Range AVDD : = +12V to +24V (+/-10%) AVSS : = -12V to -24V (+/-10%) Output Loop Compliance to AVDD - 2.5 V Temperature Range: -40C to +105C LFCSP Packages
AD5750
Voltage output is provided from a separate pin that can be configured to provide 0V to 5V, 0V to 10V, 5V or 10V output ranges. An over-range of 20% is available on the voltage ranges. Analog outputs are short and open circuit protected and can drive capacitive loads of 1uF and inductive loads of 0.1H. The device is specified to operate with a power supply range from 12 V to 24 V. Output loop compliance is 0 V to AVDD - 2.5 V. The flexible serial interface is SPI and MICROWIRE compatible and can be operated in 3-wire mode to minimize the digital isolation required in isolated applications. The interface also features an optional PEC error checking feature using CRC-8 error checking, useful in industrial environments where data communication corruption can occur. The device also includes a power-on-reset function ensuring that the device powers up in a known state and an asynchronous CLEAR pin which sets the outputs to zero-scale / mid-scale voltage output or the low end of the selected current range. A HW SELECT pin is used to configure the part for hardware or software mode on power up. The total output error is typically 0.1% in both current mode and voltage mode. Table 1. Related Devices
Part Number AD5422 Description Single Channel, 16-Bit, Serial Input Current Source and Voltage Output DAC
APPLICATIONS
Process Control Actuator Control PLC
GENERAL DESCRIPTION
The AD5750 is a single channel, low-cost, precision, voltage/current output driver with hardware or software programmable output ranges. The software ranges are configured via an SPI/Microwire compatible serial interface. The AD5750 targets applications in PLC and industrial process control. The analog input to the AD5750 is provided from a low voltage, single supply digital-to-analog converter and is internally conditioned to provide the desired output current/voltage range. The output current range is programmable across five current ranges - 4-20mA, 0-20mA or 0-24mA, 20ma and 24ma.
Rev. PrC
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2008 Analog Devices, Inc. All rights reserved.
AD5750 TABLE OF CONTENTS
Features .............................................................................................. 1 Applications ....................................................................................... 1 General Description ......................................................................... 1 Revision History ............................................................................... 2 Functional Block Diagram .............................................................. 3 Specifications..................................................................................... 4 Timing Characteristics ................................................................ 8 Absolute Maximum Ratings.......................................................... 10 ESD Caution ................................................................................ 10 Pin Configuration and Function Descriptions ........................... 11 Typical Performance Characteristics ........................................... 13 Terminology .................................................................................... 14 Theory of Operation ...................................................................... 15 CURRENT OUTPUT Architecture ......................................... 17 OUTEN ........................................................................................ 17 Software control: ......................................................................... 18
Preliminary Technical Data
HARDWARE CONTROL: ........................................................ 20 Transfer Function ....................................................................... 21 Features ............................................................................................ 22 output fault alert - SOFTWARE MODE ................................ 22 output fault alert - HARDWARE MODE ............................... 22 voltage output short circuit protection .................................... 22 Asynchronous Clear (CLEAR) ................................................. 22 External current setting resistor ............................................... 22 Applications Information .............................................................. 24 Transient voltage protection ..................................................... 24 Layout Guidelines....................................................................... 24 Galvanically Isolated Interface ................................................. 24 Microprocessor Interfacing ....................................................... 24 Outline Dimensions ....................................................................... 25 Ordering Guide .......................................................................... 25
REVISION HISTORY
PrC - Preliminary Version. May 6, 2008
Rev. PrC | Page 2 of 25
Preliminary Technical Data FUNCTIONAL BLOCK DIAGRAM
DVCC GND CLEAR CLRSEL SCLK/OUTEN* SDIN/R0* SYNC/RSEL* SDO/VFAULT* HW SELECT VIN VREF
R2 INPUT SHIFT REGISTER AND CONTROL LOGIC
AD5750
AVDD GND
COMP1
COMP2
VSENSE+
VOUT RANGE SCALING
VOUT SHORT FAULT
VOUT
VSENSESTATUS REG V DD
R3
RESET
OVERTEMP
IOUT RANGE SCALING
RSET Vx
REXT1 REXT2 IOUT
FAULT/TEMP* NC/IFAULT*
VOUT SHORT FAULT IOUT OPEN FAULT OUTPUT RANGE ERROR
POWER ON RESET
V SS
AD5750
AD2/R1* AD1/R2* AD0/R3*
IOUT OPEN FAULT
AVSS
Figure 1. Functional Block Diagram
* Denotes shared pin. Software mode denoted by regular text, hardware mode denoted by bold text. E.G. for FAULT/TEMP pin, in software mode this pin will take on FAULT function. In Hardware mode, this pin will take on TEMP function.
Rev. PrC | Page 3 of 25
AD5750 SPECIFICATIONS
Preliminary Technical Data
HL =
AVDD/AVSS=12V (+/-10%) to 24V (+/-10%) , DVCC =2.7 V to 5.5 V, GND = 0 V. RL = 2 k, CL = 200 pF, IOUT : RL = 300, 50mH; All specifications TMIN to TMAX, unless otherwise noted. Table 2.
Parameter INPUT VOLTAGE RANGE Input Leakage Current VOLTAGE OUTPUT Output Voltage Ranges B grade1 0 to 4.096 1 A grade2 0 to 4.096 1 Unit V uA max Test Conditions/Comments
0 to 5 0 to 10 -5 to +5 -10 to +10
0 to 5 0 to 10 -5 to +5 -10 to +10
V V V V
AVDD needs to have minimum 1.1v headroom, or > +11.1v. AVDD/AVSS needs to have minimum 1.1v headroom, or > +/-11.1v. Output unloaded Over temperature and supplies.
ACCURACY Bipolar Output Total Unadjusted Error (TUE) Relative Accuracy (INL) Bipolar Zero Error Bipolar Zero TC Offset Error Zero Scale Error Zero Scale TC Gain Error Gain Error TC Full Scale Error Full Scale Error TC
0.1 0.02 0.01 TBD 0.015 0.015 TBD 0.005 TBD 0.015 TBD
0.3 0.02 0.01 TBD 0.015 0.015 TBD 0.005 TBD 0.015 TBD
% FSR max % FSR max % FSR typ ppm % FSR max % FSR typ % FSR typ ppm % FSR max % FSR typ ppm % FSR max % FSR typ ppm % FSR max
Error at analog input = mid scale Error at analog input = 10mv Error at analog input = 0.0v (Ideal Span - Measured Span)/Ideal Span Error at analog input = 4.096v (FS)
Unipolar Output Total Unadjusted Error (TUE) Relative Accuracy (INL) Offset Error Zero Scale Error Zero Scale TC Gain Error Gain Error TC Full Scale Error Full Scale Error TC
0.1 0.02 0.01 0.015 TBD 0.003 TBD 0.01 TBD
0.1 0.02 0.01 0.015 TBD 0.003 TBD 0.01 TBD
% FSR max % FSR max % FSR typ % FSR typ ppm % FSR max % FSR typ ppm % FSR max % FSR typ ppm % FSR max
Over temperature and supplies.
Error at analog input = 10mv Error at analog input = 0.0v (Ideal Span - Measured Span)/Ideal Span Error at analog input = 4.096v (FS)
Output Voltage Over-Ranges
0 to 6 0 to 12 -6 to +6 -12 to +12 0.02
0 to 6
0 to 12 -6 to +6 -12 to +12
V V V V % FSR max
Programmable Over-Ranges. See Features Section.
Overrange Relative Accuracy (INL) OUTPUT CHARACTERISTICS
0.02
Rev. PrC | Page 4 of 25
Preliminary Technical Data
Parameter Short-Circuit Current Load Conditions Resistance Capacitance Load Stability RL = RL = 2 k RL = 0.1% Settling Time Slew Rate Output Noise Output Noise Spectral Density DC Output Impedance DC PSRR AC PSRR Power-On Glitch Energy CURRENT OUTPUT Output Current Ranges B grade1 15 1 20 TBD 1 10 1 TBD 80 100 0.3 10 TBD 10 0 to 24 0 to 20 4 to 20 20 24 0.1 5 A grade2 15 1 20 TBD 1 10 1 TBD 80 100 0.3 10 TBD 10 0 to 24 0 to 20 4 to 20 20 24 0.3 5 Unit mA max K Ohm min nF max nF max F max Us V/s typ V rms max V rms max nV/Hz typ typ V/V dB nV-sec typ mA mA mA mA mA % FSR max ppm max With External Precision Resistor With External Precision Resistor Test Conditions/Comments
AD5750
For Specified Performance
External compensation capacitor of 4nF connected. Specified with 200pF load
0.1 Hz to 10 Hz Bandwidth 100 kHz Bandwidth Measured at 10KHz
200mV 50/60Hz Sinewavesuperimposed on power supply voltage.
ACCURACY Total Unadjusted Error (TUE) TUE TC
Bipolar Output Relative Accuracy (INL) Bipolar Zero Error Bipolar Zero TC Offset Error Zero Scale Error Zero Scale TC Gain Error Gain Error TC Full Scale Error Full Scale Error TC Unipolar Output Relative Accuracy (INL) Offset Error Zero Scale Error Zero Scale TC Gain Error Gain Error TC Full Scale Error Full Scale Error TC
0.02 0.0325 TBD 0.0175 0.0175 TBD 0.01 TBD 0.0125 TBD
0.02 0.0325 TBD 0.0175 0.0175 TBD 0.01 TBD 0.0125 TBD
% FSR max % FSR typ ppm % FSR max % FSR typ % FSR typ ppm % FSR max % FSR typ ppm % FSR max % FSR typ ppm % FSR max
Error at analog input = mid scale Error at analog input = 10mv Error at analog input = 0.0v (Ideal Span - Measured Span)/Ideal Span Error at analog input = 4.096v (FS)
0.02 0.01 0.01 TBD 0.15 TBD 0.01 TBD
0.02 0.01 0.01 TBD 0.15 TBD 0.01 TBD
% FSR max % FSR typ % FSR typ ppm % FSR max % FSR typ ppm % FSR max % FSR typ ppm % FSR max
Error at analog input = 10mv Error at analog input = 0.0v (Ideal Span - Measured Span)/Ideal Span Error at analog input = 4.096v (FS)
Rev. PrC | Page 5 of 25
AD5750
Parameter Total Unadjusted Error (TUE) TUE TC B grade1 0.3 20 50 A grade2 0.3 20 50 Unit % FSR max ppm typ ppm max
Preliminary Technical Data
Test Conditions/Comments With Internal Resistor With Internal Resistor
Bipolar Output Relative Accuracy (INL) Bipolar Zero Error Bipolar Zero TC Offset Error Zero Scale Error Zero Scale TC Gain Error Gain Error TC Full Scale Error Full Scale Error TC Unipolar Output Relative Accuracy (INL) Offset Error Zero Scale Error Zero Scale TC Gain Error Gain Error TC Full Scale Error Full Scale Error TC CURRENT MODE OVERRANGES
0.02 0.0325 TBD 0.01 0.01 TBD 0.003 TBD 0.01 TBD
0.02 0.0325 TBD 0.01 0.01 TBD 0.003 TBD 0.01 TBD
% FSR max % FSR typ ppm % FSR max % FSR typ % FSR typ ppm % FSR max % FSR typ ppm % FSR max % FSR typ ppm % FSR max
Error at analog input = mid scale Error at analog input = 10mv Error at analog input = 0.0v (Ideal Span - Measured Span)/Ideal Span Error at analog input = 4.096v (FS)
0.02 0.01 0.01 TBD 0.005 TBD 0.01 TBD 0 to 24.5 0 to 20.4 4 to 20.4
0.02 0.01 0.01 TBD 0.005 TBD 0.01 TBD 0 to 24.5 0 to 20.4 4 to 20.4
% FSR max % FSR typ % FSR typ ppm % FSR max % FSR typ ppm % FSR max % FSR typ ppm % FSR max mA mA mA
Error at analog input = 10mv Error at analog input = 0.0v (Ideal Span - Measured Span)/Ideal Span Error at analog input = 4.096v (FS)
SEE FEATURES SECTION SEE FEATURES SECTION SEE FEATURES SECTION
OUTPUT CHARACTERISTICS Current Loop Compliance Voltage Resistive Load Inductive Load 0.1% Settling Time DC PSRR Output Impedance
AVDD - 2.5 See Comment 0.1 10 1 25
AVDD - 2.5 See Comment 0.1 10 1 25
V max k max H max us A/V max M typ Chosen such that compliance is not exceeded.
REFERENCE INPUT Reference Input Reference Input Voltage Input Leakage Current DIGITAL INPUTS VIH, Input High Voltage VIL, Input Low Voltage Input Current Pin Capacitance
4.096 1 2 0.8 1 10
4.096 1 2 0.8 1 10
V nom uA max V min V max A max pF typ
Rev. PrC | Page 6 of 25
1% for specified performance DVCC = 2.7 V to 5.5 V, JEDEC compliant
Per pin Per pin
Preliminary Technical Data
Parameter DIGITAL OUTPUTS FAULT, IFAULT, TEMP, VFAULT VOL, Output Low Voltage VOL, Output Low Voltage VOH, Output High Voltage SDO VOL, Output Low Voltage VOH, Output High Voltage High Impedance Leakage current High Impedance Output Capacitance POWER REQUIREMENTS AVDD AVSS DVCC Input Voltage AVDD AVSS DICC Power Dissipation B grade1 A grade2 Unit Test Conditions/Comments
AD5750
0.4 0.6 3.6
0.4 0.6 3.6
V max V typ V min
10k pull-up resistor to DVCC @ 2.5 Ma 10k pull-up resistor to DVCC
0.5 DVCC-0.5 TBD 20
0.5 DVCC-0.5 TBD 20
V max V min ua max pF max
Sinking 200ua Sourcing 200ua
12 to 24 -12 to 24 2.7 to 5.5 TBD TBD TBD TBD
12 to 24 -12 to 24 2.7 to 5.5 TBD TBD TBD TBD
V min to V max V min to V max V min to V max mA mA mA max mW typ
+/-10% +/-10% Internal supply disabled Output unloaded Output unloaded VIH = DVCC, VIL = GND, TBD mA typ
1 2
Temperature range: -40C to +105C; typical at +25C. Temperature range: -40C to +105C; typical at +25C.
Rev. PrC | Page 7 of 25
AD5750
TIMING CHARACTERISTICS
Preliminary Technical Data
AVDD/AVSS=12V (+/-10%) to 24V (+/-10%) , DVCC =2.7 V to 5.5 V, GND = 0 V. RL = 2 k, CL = 200 pF, IOUT : RL = 300, 50mH; All specifications TMIN to TMAX, unless otherwise noted. Table 3.
Parameter1, 2 t1 t2 t3 t4 t5 t6 t7 t8 t10 , t9 t11 t12 Limit at TMIN, TMAX 33 13 13 13 13 13 6 0 1 25 25 Unit ns min ns min ns min ns min ns min ns min ns min ns min s max ns min ns max Description SCLK cycle time SCLK high time SCLK low time SYNC falling edge to SCLK falling edge setup time 16th SCLK falling edge to SYNC rising edge Minimum SYNC high time (WRITE MODE) Data setup time Data hold time CLEAR pulse high/low activation time Minimum SYNC high time (READ MODE) SCLK rising edge to SDO valid (SDO CL=20pf )
HL =
1 Guaranteed by characterization. Not production tested. 2 All input signals are specified with tR = tF = 5 ns (10% to 90% of DVCC) and timed from a voltage level of 1.2 V.
200A
IOL
TO OUTPUT PIN
VOH(min)-VOL(max) CL 15pF 200A IOH 2
SDO Load Timing.
Rev. PrC | Page 8 of 25
Preliminary Technical Data
t1
SCLK 1 2 16
AD5750
t6 t4
SYNC
t3
t2 t5
t7
SDIN DB15
t8
DB0
CLEAR
t10
VOUT
t9
Figure 2. Write Mode Timing Diagram
16
1 SCLK
2
SYNC
t11
SDIN
A2
A1
A0
R=1
0
X
X
X
X
X
X
X
X
X
X
X
t12
SDO X X X X X R3 R2 R1 R0
CLRSEL OUTEN
RSEL
PEC Error
OVER TEMP
IOUT Fault
VOUT Fault
Figure 3. Readback Mode Timing Diagram
Rev. PrC | Page 9 of 25
AD5750 ABSOLUTE MAXIMUM RATINGS
Preliminary Technical Data
TA = 25C unless otherwise noted. Transient currents of up to 100 mA do not cause SCR latch-up. Table 4.
Parameter AVDD to GND AVSS to GND AVDD to AVSS DVCC to GND +VSENSE to GND -VSENSE to GND Digital Inputs to GND Digital Outputs to GND REFIN/REFOUT to GND VIN to GND VOUT to GND IOUT to GND Operating Temperature Range Industrial Storage Temperature Range Junction Temperature (TJ max) 32-Lead LFCSP Package JA Thermal Impedance Lead Temperature Soldering Rating -0.3V to 30v +0.3 V to -30v -0.3V to 60v -0.3 V to +7 V AVSS to AVDD +/-5.0v -0.3 V to DVCC + 0.3 V or 7 V (whichever is less) -0.3 V to DVCC + 0.3 V or 7V (whichever is less) -0.3 V to +5 V -0.3 V to +5 V AVSS to AVDD -0.3V to AVDD, +0.3V to AVSS -40C to +105C -65C to +150C 125C 28C/W JEDEC Industry Standard J-STD-020
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ESD CAUTION
Rev. PrC | Page 10 of 25
Preliminary Technical Data PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
NC/IFAULT FAULT/TEMP RESET HW SELECT NC NC NC NC
AD5750
32 31 30 29 28 27 26 25
Figure 4. LFCSP Pin Configuration
Table 5. Pin Function Descriptions
LFCSP Pin No. 1 Mnemonic SDO/VFAULT Description In Software Mode, Serial Data Output. Used to clock data from the serial register in readback mode. Data is clocked out on the rising edge of SCLK and is valid on the falling edge of SCLK. Open Drain Output, must be connected to a pull up resistor. In Hardware mode, acts as a SHORT circuit Fault alert pin. This pin is asserted low when an SHORT circuit. Error is detected. Open drain output, must be connected to a pull-up resistor. 2 CLRSEL In Hardware or software mode, selects the clear value, either zero-scale or mid-scale code. In Software mode, this pin is implemented as a logic OR with the internal CLRSEL bit. Active High Input. Asserting this pin sets the Output Current/Voltage to zero-scale code or mid-scale code of range selected (user-selectable). CLEAR is a LOGIC OR with the internal CLEAR bit. Digital Power Supply Ground Connection. In Software Mode, Positive edge sensitive latch, a rising edge will parallel load the input shift register data into the INPUT register, also updating the output. In Hardware mode, this pin chooses whether internal/external current sense resistor is used In Software Mode, Serial Clock Input. Data is clocked into the shift register on the falling edge of SCLK. This operates at clock speeds up to 30 MHz. In Hardware mode, this pin acts as an output enable pin. In Software Mode, Serial Data Input. Data must be valid on the falling edge of SCLK. In Hardware Mode, R0 is Range Decode Bit. This pin, in conjunction with R2, R3, R1 choose the output current/voltage range setting on the part. In Software Mode, AD2 is Device Addressing bit. This pin, in conjunction with AD1, AD0 allow up to 8 devices to be addressed on one bus. In Hardware Mode, R1 is Range Decode Bit. This pin, in conjunction with R2, R3, R0 choose the output current/voltage range setting on the part. In Software Mode, AD1 is Device Addressing bit. This pin, in conjunction with AD2, AD0 allow up to 8 devices to be addressed on one bus.
Rev. PrC | Page 11 of 25
3
CLEAR
4 5 6
DVCC GND SYNC/RSEL
7
SCLK/OUTEN
8
SDIN/RO
9
AD2/R1
10
AD1/R2
AD2/R1 AD1/R2 AD0/R3 REXT2 REXT1 VREF VIN GND
9 10 11 12 13 14 15 16
NC = NO CONNECT
00000-000
SDO/VFAULT 1 CLRSEL 2 CLEAR 3 DVCC 4 GND 5 SYNC/RSEL 6 SCLK/OUTEN 7 SDIN/R0 8
PIN 1 INDICATOR
TOP VIEW
24 23 22 21 20 19 18 17
VSENSE+ VOUT VSENSEAVSS COMP1 COMP2 IOUT AVDD
AD5750
LFCSP Pin No. Mnemonic
Preliminary Technical Data
Description In Hardware Mode, R2 is Range Decode Bit. This pin, in conjunction with R3, R1, R0 choose the output current/voltage range setting on the part. In Software Mode, AD0 is Device Addressing bit. This pin, in conjunction with AD1, AD2 allow up to 8 devices to be addressed on one bus. In Hardware Mode, R3 is Range Decode Bit. This pin, in conjunction with R2, R1, R0 choose the output current/voltage range setting on the part. An external current setting resistor can be connected to this pin to improve the IOUT temperature drift performance. When using the Internal RSET resistor these pins must be left floating. Reference Input Analog Input (0-4.096v) Ground Connection. Positive Analog Supply Pin. Current Output Pin Optional compensation capacitor connection for the voltage output buffer Optional compensation capacitor connection for the voltage output buffer Negative Analog Supply Pin. Sense connection for the negative voltage output load connection. This pin must stay within +/-3.0v of ground for correct operation. Buffered Analog Output Voltage. Sense connection for the positive voltage output load connection. No Connect Pin. Can be tied to GND. This part is used to configure the part to hardware/software mode. HW SELECT = 0 selects Software Control. HW SELECT = 1 selects Hardware Control. Resets the part to its power on state. In Software mode, acts as a general Fault alert pin. This pin is asserted low when an open circuit, short circuit, over temperature or PEC Interface Error is detected. Open drain output, must be connected to a pull-up resistor. In Hardware mode, acts as an over temp FAULT pin. This pin is asserted low when an over temperature Error is detected. Open drain output, must be connected to a pull-up resistor. In Hardware mode, acts as a OPEN circuit Fault alert pin. This pin is asserted low when an OPEN circuit. Error is detected. Open drain output, must be connected to a pull-up resistor. In Software mode, is a NC. Tie to GND.
11
AD0/R3
12 13
REXT1 REXT 2
14 15 16 17 18 19 20 21 22 23 24 25,26,27,28 29
VREF VIN GND AVDD IOUT COMP1 COMP2 AVSS -VSENSE VOUT +VSENSE NC HW SELECT
30 31
RESET FAULT/TEMP
32
NC/IFAULT
Rev. PrC | Page 12 of 25
Preliminary Technical Data TYPICAL PERFORMANCE CHARACTERISTICS
AD5750
Figure 5.
Figure 8.
Figure 6.
Figure 9.
Figure 7.
Figure 10
Rev. PrC | Page 13 of 25
AD5750 TERMINOLOGY
Output Voltage Settling Time Output voltage settling time is the amount of time it takes for the output to settle to a specified level for a full-scale input change. A plot of settling time can be seen in Table TBD Slew Rate The slew rate of a device is a limitation in the rate of change of the output voltage. Slew rate is measured from 10% to 90% of the output signal and is given in V/s. Total Unadjusted Error Total unadjusted error (TUE) is a measure of the output error taking all the various errors into account. TUE is expressed in % FSR.
Preliminary Technical Data
Current Loop Voltage Compliance The maximum voltage at the IOUT pin for which the output currnet will be equal to the programmed value. Power-On Glitch Energy Power-on glitch energy is the impulse injected into the analog output when the AD5750 is powered-on. It is specified as the area of the glitch in nV-sec. Power Supply Rejection Ratio (PSRR) PSRR indicates how the output is affected by changes in the power supply voltage.
Rev. PrC | Page 14 of 25
AD5750 THEORY OF OPERATION
Preliminary Technical Data
Figures 11 and 12 shows a typical configuration of AD5750 in Software Mode (Figure 11) and in Hardware mode (Figure 12) in an output module system. The HW SELECT pin chooses whether the part is configured in software or hardware mode. The analog input to the AD5750 is provided from a low voltage, single supply digital-to-analog converter such as the AD5061 which provides an output range of 0-4.096V. The supply and reference for the DAC, as well as the reference for the AD5750 can be supplied from a reference such as the ADR392. The AD5750 can operate from supplies up to +26.4 volts. In current mode, software selectable output ranges include 20mA, 24mA, 0-20 mA, 4mA-20mA or 0mA-24mA. In voltage mode, software selectable output ranges include 0V-5V, 0V-10V, 5V or 10V. The current and voltage outputs are available on separate pins. Only one output can be enabled at one time. The output range is selected by programming the range bits in the control register.
VDD AGND VSS
ADP1720
AD5750
ADR392
VDD
VSENSE+ VSENSE-
REFIN
VOUT RANGE SCALE
REFIN
MCU
SCLK SDI SDO SYNC1
VOUT 0-5V, 0-10V, +/-5V, +/-10V IOUT 0-20ma, 0-24ma, 4-20ma, +/-20ma, +/-24ma.
AD566X
VIN
IOUT RANGE SCALE SERIAL INTERFACE
SYNC2
VOUT SHORT FAULT IOUT OPEN FAULT OVERTEMP FAULT RANGE ERROR STATUS REGISTER
HW SELECT
FAULT
Figure 11. Typical System Configuration in Software Mode .Pull up resistors not shown for open drain outputs.
Rev. PrC | Page 15 of 25
AD5750
Preliminary Technical Data
VDD AGND VSS
ADP1720
AD5750
ADR392
VDD
VSENSE+ VSENSE-
REFIN
VOUT RANGE SCALE
REFIN
MCU
SCLK SDI SDO SYNC1
VOUT 0-5V, 0-10V, +/-5V, +/-10V IOUT 0-20ma, 0-24ma, 4-20ma, +/-20ma, +/-24ma.
AD566X
VIN
IOUT RANGE SCALE
DVCC
HW SELECT OUTEN R3 R2 R1 VFAULT* IFAULT* R0
OUTPUT RANGE SELECT PINS
TEMP
Figure 12. Typical System Configuration in Hardware Mode. Pull up resistors not shown for open drain outputs.
Rev. PrC | Page 16 of 25
Preliminary Technical Data
CURRENT OUTPUT ARCHITECTURE
The voltage input from the analog input VIN core (0-4.096v) is either converted to a current (see Figure 12) which is then mirrored to the supply rail so that the application simply sees a current source output with respect to an internal reference voltage or it is buffered and scaled to output a software selectable unipolar or bipolar voltage range (See Figure 13). The Reference is used to provide internal offsets for range and gain scaling. The selectable output range is programmable through the digital interface.
VDD R2 RANGE DECODE FROM INTERFACE REXT1 VIN VREF IOUT RANGE SCALING R1 RSET REXT2 R3
AD5750
Driving Large Capacitive Loads
The voltage output amplifier is capable of driving capacative loads of up to 1uF with the addition of a non-polarised 4nF compensation capacitor between the CCOMP1 and CCOMP2 pins. Without the compensation capacitor, up to 20nF capacitive loads can be driven. POWER ON STATE OF AD5750 On Power-up, the AD5750 will sense whether hardware or software mode is loaded and set the power up conditions accordingly. In software SPI mode, the part will power up with all outputs disabled (OUTEN bit=0). In disabled mode, both the current and voltage outputs are put into tri-state mode. The user will have to set the OUTEN bit in the control register to enable the output and in the same write the user will also set the output range configuration using the range bits. If hardware mode is selected, the part will power up to the conditions defined by the range bits and the status of the OUTEN pin. It is recommended to keep the output disabled when powering up the part in hardware mode. RESET: The AD5750 contains a reset function.
VINT
IOUT
VSS
R4
IOUT OPEN FAULT
Figure 11. Current Output Configuration
RANGE DECODE FROM INTERFACE +VSENSE VIN (0-4.096V) VREF VOUT RANGE SCALING
VOUT
VOUT SHORT FAULT -VSENSE
Figure 12. Voltage Output
Voltage Output Amplifier
The voltage output amplifier is capable of generating both unipolar and bipolar output voltages. It is capable of driving a load of 1 k in parallel with 1.2 uF. The source and sink capabilities of the output amplifier can be seen in Figure TBD. The slew rate is 1 V/s with a full-scale settling time of 10 s.(10V step). The current and voltage are output on separate pins and cannot be output simultaneously. This allows the user to tie both the current and voltage output pins together and configuring the end system as "one channel" output.
In Software mode, the part can be reset using the RESET pin (active low) or the RESET bit (RESET=1). A reset will disable both the current and voltage outputs and put them in tri-state mode. The user will have to write to the OUTEN bit to enable the output and in the same write the user will also set the output range configuration. The RESET pin is a level sensitive input the part will stay in RESET mode as long as RESET pin is low. The RESET bit will clear to zero following a RESET command to the control register. In hardware mode, there is no RESET. If using the part in hardware mode the RESET pin should be tied high.
OUTEN
In Software mode, the output can be enabled/disabled using the OUTEN bit in the control register. When the output is disabled, both the current and voltage channels both go into tri-state. The user will have to set the OUTEN bit to enable the output and at this time the user will also set the output range configuration. In Hardware mode, the output can be enabled/disabled using the OUTEN pin. When the output is disabled, both the current and voltage channels both go into tri-state. The user will have to write to the OUTEN pin to enable the output. It is recommended that the output be disabled when changing the ranges.
Rev. PrC | Page 17 of 25
AD5750
SOFTWARE CONTROL:
Preliminary Technical Data
Software control is enabled by connecting the HW SELECT pin to ground. In software mode, the AD5750 is controlled over a versatile 3wire serial interface that operates at clock rates up to 30 MHz. It is compatible with SPI(R), QSPITM, MICROWIRETM, and DSP standards The input shift register is 16 bits wide. Data is loaded into the device MSB first as a 16-bit word under the control of a serial clock input, SCLK. Data is clocked in on the falling edge of SCLK. The input register consists of 16 control bits as shown in Table 5. The timing diagram for this operation is shown in Figure 2. The first 3 bits of the Input Register are used to set the hardware address of the AD5750 device on the PCB board. Up to 8 devices can be addressed per board. Bits D11, D1, D0 must always be set to 0 during any write sequence. Table 3. Input Shift Register Format
MSB D15 A2 D14 A1 D13 A0 D12 R/W D11 0 D10 R3 D9 R2 D8 R1 D7 R0 D6 CLRSEL D5 OUTEN D4 CLEAR D3 RSEL D2 RESET D1 0 LSB D0 0
Table 6. Input Shift Register Decoded
Register A2, A1, A0 Used in association with External Pins AD2, AD1, AD0 to determine which part is being addressed by the system controller. A2 A1 A0 Function 0 0 0 0 1 1 1 1 R/W CLEAR CLRSEL
0 0 1 1 0 0 1 1
0 1 0 1 0 1 0 1
Addresses Part with pins AD2=0, AD1=0, Addresses Part with pins AD2=0, AD1=0, Addresses Part with pins AD2=0, AD1=1, Addresses Part with pins AD2=0, AD1=1, Addresses Part with pins AD2=1, AD1=0, Addresses Part with pins AD2=1, AD1=0, Addresses Part with pins AD2=1, AD1=1, Addresses Part with pins AD2=1, AD1=1,
AD0=0 AD0=1 AD0=0 AD0=1 AD0=0 AD0=1 AD0=0 AD0=1
Indicates a read from or a write to the addressed register. Software Clear Bit - Active High. Sets Clear Mode to zero scale or midscale. See Text. CLRSEL 0 1
Clear to Zero Volts Clear to Mid Scale in Unipolar Mode, Clear to Zero Scale in Bipolar Mode.
OUTEN RSEL
Output Enable Bit. This bit must be set to 1 to enable the outputs. Select Internal/External Current Sense Resistor. RSEL 1 Select Internal Current Sense Resistor /*used with Range bits to select Range */ 0
Select External Current Sense Resistor /*used with Range bits to select Range */
R3 0 0 0 0 0 0 0 0 1 1 1 1
R3,R2,R1,R0
Selects output Configuration in conjunction with RSEL. RSEL 0 0 0 0 0 0 0 0 0 0 0 0
R2 0 0 0 0 1 1 1 1 0 0 0 0
R1 0 0 1 1 0 0 1 1 0 0 1 1
R0 0 1 0 1 0 1 0 1 0 1 0 1
Output Configuration 4-20MA External Current Sense Resistor 15k ohm. 0-20MA External Current Sense Resistor 15k ohm. 0-24MA External Current Sense Resistor 15k ohm. +/-20MA External Current Sense Resistor 15k ohm. +/-24MA External Current Sense Resistor 15k ohm. 0-5V 0-10V +/-5V +/-10V 0-6.0V (20% over range) 0-12.0V (20% over range) +/-6.0V (20% over range)
Rev. PrC | Page 18 of 25
Preliminary Technical Data
0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Reset 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
AD5750
0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 +/-12.0V (20% over range) +/-2.5v N/A. If selected output will drive 0V. N/A. If selected output will drive 0V. 4-20MA Internal Current Sense Resistor. 0-20MA Internal Current Sense Resistor. 0-24MA Internal Current Sense Resistor. +/-20MA +/-24MA 0-5V 0-10V +/-5V +/-10V 0-6.0V (20% over range) 0-12.0V (20% over range) +/-6.0V (20% over range) +/-12.0V (20% over range) 3.92ma - 20.4ma Internal Current Sense Resistor. 0ma - 20.4ma Internal Current Sense Resistor. 0ma - 24.5ma Internal Current Sense Resistor.
Resets the part to its Power on State
1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
Readback Operation
Readback mode is invoked by selecting the correct device address (A2,A1,A0) and then setting the R/W bit to 1. By default the SDO pin is disabled, after having addressed the AD5750 for a read operation, setting R/W to 1 will enable the SDO pin and SDO data will be clocked out on the 5th rising edge of SCLK. After the data has been clocked out on SDO, a rising edge on SYNC will disable (tri- state) the SDO pin once again. STATUS and CONTROL register data will be both available during the same read cycle. See Table 7 below.
Table 7. Input Shift Register Contents for a read operation
MSB D15 A2 D14 A1 D13 A0 D12 1 D11 0 D10 R3 D9 R2 D8 R1 D7 R0 D6 CLRSEL D5 OUTEN D4 RSEL D3 D2 OVER TEMP D1 IOUT Fault LSB D0 Vout Fault
PEC Error Bit
The STATUS bits are 4 read only bits. They are used to notify the user of specific fault conditions that have arisen, such as open or short circuit on the output, over temperature, or an interface error. If any one of these fault conditions occur a hardware FAULT is also asserted low which can be used as a hardware interrupt to the controller. Full explanation of fault conditions are given in the Features sections.
Table 9. STATUS Bits Options
Option PEC ERROR VOUT FAULT IOUT FAULT OVER TEMP Description Bit Set if there is an Interface Error detected by CRC-8 Error Checking. See features section. Bit set if there is a short Circuit on VOUT pin. Bit set is there is an open circuit on IOUT pin. This bit will be set if the AD5750 core temperature exceeds approx. 150C.
Rev. PrC | Page 19 of 25
AD5750
HARDWARE CONTROL:
Preliminary Technical Data
Hardware control is enabled by connecting the HW SELECT pin to DVCC. In this mode, pins R3,R2,R1,R0 along with RSEL pin are used to configure the output range as per Table.
RSEL 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
R3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
R2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
R1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
R0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
Output Configuration 4-20MA External Current Sense Resistor 15k ohm. 0-20MA External Current Sense Resistor 15k ohm. 0-24MA External Current Sense Resistor 15k ohm. +/-20MA External Current Sense Resistor 15k ohm. +/-24MA External Current Sense Resistor 15k ohm. 0-5V 0-10V +/-5V +/-10V 0-6.0V (20% over range) 0-12.0V (20% over range) +/-6.0V (20% over range) +/-12.0V (20% over range) +/-2.5v N/A. If selected output will drive 0V. N/A. If selected output will drive 0V. 4-20MA Internal Current Sense Resistor. 0-20MA Internal Current Sense Resistor. 0-24MA Internal Current Sense Resistor. +/-20MA +/-24MA 0-5V 0-10V +/-5V +/-10V 0-6.0V (20% over range) 0-12.0V (20% over range) +/-6.0V (20% over range) +/-12.0V (20% over range) 3.92ma - 20.4ma Internal Current Sense Resistor. 0ma - 20.4ma Internal Current Sense Resistor. 0ma - 24.5ma Internal Current Sense Resistor.
Rev. PrC | Page 20 of 25
Preliminary Technical Data
In hardware mode there is no status register. The fault conditions; open circuit, short circuit and over temperature are available on pins IFAULT, VFAULT and TEMP. If any one of these fault conditions are set then a low is asserted on the specific fault pin. IFAULT, VFAULT and TEMP are open drain outputs and therefore can be connected together to allow the user generate one interrupt to the system controller to communicate a fault. If hardwired in this way, it will not be possible to isolate which fault occurred in the system. DEFAULT CONFIGURATION: On initial power-up of the AD5750 the power-on-reset circuit ensures that all registers are loaded with zero-code, as such the default output is the current output with the 4mA to 20mA range selected, the current output until a value is programmed is 0mA. The voltage output pin will be in three-state. An alternative current range or a voltage output range may be selected via the CONTROL register. Vout = GAIN x VIN
AD5750
For a bipolar voltage output range, the output voltage expression is given by Vout = (GAIN x VIN - (GAIN x (VREF/2)) x VIN) where: VREF is the reference voltage applied at the REFIN pin. Gain is an internal gain whose value depends on the output range selected by the user as shown in
Current Output For a given current output range, the current output range is chosen setting the bits R3,R2,R1,R10 in the Input Register or pins. Transfer function will change depending on current range selected.
TRANSFER FUNCTION
Voltage Output
For a unipolar voltage output range, the output voltage expression is given by
Rev. PrC | Page 21 of 25
AD5750 FEATURES
OUTPUT FAULT ALERT - SOFTWARE MODE
In Software mode, the AD5750 is equipped with one FAULT pin, this is an open-drain output allowing several AD5750 devices to be connected together to one pull-up resistor for global fault detection. In software control mode, the FAULT pin is forced active high by any one of the following fault scenarios; 1) The Voltage at IOUT attempts to rise above the compliance range, due to an open-loop circuit or insufficient power supply voltage. The internal circuitry that develops the fault output avoids using a comparator with "window limits" since this would require an actual output error before the FAULT output becomes active. Instead, the signal is generated when the internal amplifier in the output stage has less than approximately one volt of remaining drive capability. Thus the FAULT output activates slightly before the compliance limit is reached. Since the comparison is made within the feedback loop of the output amplifier, the output accuracy is maintained by its open-loop gain and an output error does not occur before the FAULT output becomes active. A short is detected on the voltage output pin. Short circuit current limited to 25ma. An interface error is detected due to the PEC error checking failure. See PEC error checking section. A range change is detected without the user writing to the Interface. If the core temperature of the AD5750 exceeds approx. 150C.
Preliminary Technical Data
feedback loop of the output amplifier, the output accuracy is maintained by its open-loop gain and an output error does not occur before the FAULT output becomes active. If this fault is detected the IFAULT pin is forced low. 2) A short is detected on the voltage output pin. Short circuit current limited to 25ma. If this fault is detected the VFAULT pin is forced low. If the core temperature of the AD5750 exceeds approx. 150C. If this fault is detected the TEMP pin is forced low.
3)
VOLTAGE OUTPUT SHORT CIRCUIT PROTECTION
Under normal operation the voltage output will sink/source 5mA and maintain specified operation. The maximum current that the voltage output will deliver is 15mA, this is the short circuit current.
ASYNCHRONOUS CLEAR (CLEAR)
CLEAR is an active high clear that allows the voltage output to be cleared to either zero-scale code or mid-scale code, userselectable via the CLRSEL pin or the CLRSEL bit of the INPUT register as described in Table 6. (The Clear select feature is a logical OR function of the CLR SELECT pin and the CLRSEL bit). The Current loop output will clear to the bottom of its programmed range. It is necessary to maintain CLEAR high for a minimum amount of time (see Figure 2) to complete the operation. When the CLEAR signal is returned low, the output returns to its programmed value or a new value if programmed. A clear operation can also be performed via the CLEAR command in the control register. Table 11. CLEAR SELECT Options
2) 3) 4) 5)
OUTPUT FAULT ALERT - HARDWARE MODE
In hardware mode, the AD5750 is equipped with 3 FAULT pins, VFAULT, IFAULT, TEMP. These are an open-drain outputs allowing several AD5750 devices to be connected together to one pull-up resistor for global fault detection. In hardware control mode, these fault pins are forced active by any one of the following fault scenarios; 1) Open Circuit Detect. The Voltage at IOUT attempts to rise above the compliance range, due to an open-loop circuit or insufficient power supply voltage. The internal circuitry that develops the fault output avoids using a comparator with "window limits" since this would require an actual output error before the FAULT output becomes active. Instead, the signal is generated when the internal amplifier in the output stage has less than approximately one volt of remaining drive capability. Thus the FAULT output activates slightly before the compliance limit is reached. Since the comparison is made within the
CLR SELECT
Output CLR Value Unipolar Output Voltage Range 0V Mid-Scale Unipolar Current Output Range Zero-Scale e.g. 4ma on 4-20ma 0ma on 0-20ma etc... Mid-Scale e.g. 12ma on 4-20ma 10ma on 0-20ma Bipolar Output Range Negative Full-Scale 0V Bipolar Current Output Range Zero Scale e.g. -24ma on +/-24ma Mid-Scale e.g. 0ma on +/-24ma
0 1
0
1
EXTERNAL CURRENT SETTING RESISTOR
Referring to Figure 1, RSET is an internal sense resistor as part of the voltage to current conversion circuitry. The nominal value of internal current sense resistor is 15k ohm. To allow for overrange capability in current mode, the user can also select
Rev. PrC | Page 22 of 25
Preliminary Technical Data
the internal current sense resistor to be 14.7K, giving a nominal 2% overrange capability. This feature is available in the 0-20ma, 4-20ma, +/-20ma current ranges. The stability of the output current value over temperature is dependent on the stability of the value of RSET. As a method of improving the stability of the output current over temperature an external low drift resistor can be connected to the RSET1 & RSET2 pins of the AD5750 to be used instead of the internal resistor RSET. The external resistor is selected via the input register. If the external resistor option is not used the RSET1 and RSET2 pins should be left floating.
AD5750
PACKET ERROR CHECKING
To verify that data has been received correctly in noisy environments, the AD5750 offers the option of error checking based on an 8-bit (CRC-8) cyclic redundancy check. The device controlling the AD5750 should generate an 8-bit frame check sequence using the polynomial C(x) = x8 + x2 + x1 +1. This is added to the end of the data word, and 24 data bits are sent to the AD5750 before taking SYNC high. If the AD5750 sees a 24-bit data frame, it will perform the error check when SYNC goes high. If the check is valid, then the data will be written to the selected register. If the error check fails, the FAULT will go high and bit D4 of the Status Register is set. After reading this register, this error flag is cleared automatically and PEC goes high again.
UPDATE ON SYNC HIGH SYNC
PROGRAMMABLE OVER-RANGE MODES
The AD5750 contains an over range mode for most of the available ranges. In voltage mode the over-range is typically 20% and in current mode the over-range is typically 2%. The overranges are selected by configuring R3, R1, R1, R0 bits/pins accordingly. In voltage mode the overranges are typically 20% providing programmable output ranges of 0-6v, 0-12v, +/-6v and +/-12v. The 0-4.096v analog input remains the same. In current mode the overranges are typically 2%. In current mode the overrange capability is only available on 3 ranges, 020ma, 0-24ma, 4-20ma. For these ranges the analog input will also vary, according to the table below.
SCLK MSB D15 DIN 16-BIT DATA LSB D0
16-BIT DATA TRANSFER - NO ERROR CHECKING UPDATE AFTER SYNC HIGH ONLY IF ERROR CHECK PASSED
SYNC
Over Range 0-20.4ma 3.92-20.4ma 0-24.5ma
Analog Input 0.075v - 4.096v 0.06v-4.096v 0.065-4.096v
SCLK MSB D23 DIN 16 BIT DATA LSB D8 D7 D0 8-BIT FCS
PEC
PEC GOES LOW IF ERROR CHECK FAILS 16-BIT DATA TRANSFER WITH ERROR CHECKING
For example, in 0-20.4ma range, an analog input of 0.075v will output 0ma and 4.096v will output full scale 20.4ma.
Figure 13. PEC Error Checking Timing
Rev. PrC | Page 23 of 25
AD5750 APPLICATIONS INFORMATION
TRANSIENT VOLTAGE PROTECTION
The AD5750 contains ESD protection diodes which prevent damage from normal handling. The industrial control environment can, however, subject I/O circuits to much higher transients. In order to protect the AD5750 from excessively high voltage transients , external power diodes and a surge current limiting resistor may be required, as shown in Figure 15. The constraint on the resistor value is that during normal operation the output level at IOUT must remain within its voltage compliance limit of AVDD - 2.0V and the two protection diodes and resistor must have appropriate power ratings.
AVDD
Preliminary Technical Data
separate ground plane, but separating the lines helps). It is essential to minimize noise on the REFIN line. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other. This reduces the effects of feed through the board. A microstrip technique is by far the best, but not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground plane, while signal traces are placed on the solder side.
GALVANICALLY ISOLATED INTERFACE
In many process control applications, it is necessary to provide an isolation barrier between the controller and the unit being controlled to protect and isolate the controlling circuitry from any hazardous common-mode voltages that might occur. The iCoupler(R) family of products from Analog Devices provides voltage isolation in excess of 2.5 kV. The serial loading structure of the AD5750 make it ideal for isolated interfaces because the number of interface lines is kept to a minimum. Figure 16 shows a 4-channel isolated interface to the AD5750 using an ADuM1400. For further information, visit http://www.analog.com/icouplers.
AVDD
AD5750
IOUT
RP RLOAD
AVSS
Figure 15. Output Transient Voltage Protection
LAYOUT GUIDELINES
In any circuit where accuracy is important, careful consideration of the power supply and ground return layout helps to ensure the rated performance. The printed circuit board on which the AD5750 is mounted should be designed so that the AD5750 lies on the analog plane. The AD5750 should have ample supply bypassing of 10 F in parallel with 0.1 F on each supply located as close to the package as possible, ideally right up against the device. The 10 F capacitors are the tantalum bead type. The 0.1 F capacitor should have low effective series resistance (ESR) and low effective series inductance (ESI) such as the common ceramic types, which provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. The power supply lines of the AD5750 should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Fast switching signals such as clocks should be shielded with digital ground to avoid radiating noise to other parts of the board and should never be run near the reference inputs. A ground line routed between the SDIN and SCLK lines helps reduce crosstalk between them (not required on a multilayer board that has a
Controller Serial Clock Out Serial Data Out SYNC Out Control out ADuM1400 * VIA VIB VIC VID ENCODE ENCODE ENCODE ENCODE DECODE DECODE DECODE DECODE VOA VOB VOC VOD To SCLK To SDIN To SYNC To CLEAR
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure16. Isolated Interface
MICROPROCESSOR INTERFACING
Microprocessor interfacing to the AD5750 is via a serial bus that uses protocol compatible with microcontrollers and DSP processors. The communications channel is a 3-wire (minimum) interface consisting of a clock signal, a data signal, and a sync signal. The AD5750 require a 16-bit data-word with data valid on the falling edge of SCLK.
Rev. PRC | Page 24 of 25
Preliminary Technical Data OUTLINE DIMENSIONS
5.00 BSC SQ 0.60 MAX 0.60 MAX
25 24 32 1
AD5750
PIN 1 INDICATOR
PIN 1 INDICATOR TOP VIEW 4.75 BSC SQ
0.50 BSC
EXPOSED PAD (BOTTOM VIEW)
17 16 8
3.25 3.10 SQ 2.95
0.50 0.40 0.30
9
0.25 MIN 3.50 REF
12 MAX
0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM
1.00 0.85 0.80
SEATING PLANE
0.30 0.23 0.18
0.20 REF
COPLANARITY 0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2
Figure 17. 32-Lead Lead Frame Chip Scale Package (CP-32-2) Dimensions shown in millimeters
ORDERING GUIDE
Model AD5750ACPZ AD5750BCPZ TUE Accuracy 0.3 % 0.1% Temperature Range -40C to 105C -40C to 105C Package Description 32 Lead LFCSP 32 Lead LFCSP Package Option CP-32-2 CP-32-2
Rev. PrC | Page 25 of 25
PR07268-0-5/08(PrC)

▲Up To Search▲

Price & Availability of AD5750

	To Download AD5750 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .